I thought I would share this with you all. The following thread from the new Crosman Forum has some very interesting technical information about pellet penetration:
Penetration and Expansion Testing
March 6 2014 at 10:58 PM By RSterne
Here is a series of posts from a thread on another Forum where I tested a variety of pellets at several energy levels in melt-and-pour soap.... I am just copy-pasting the posts below.... The first set of tests are .22 cal at 20 FPE....
Every once in a while I try and find a new test medium for assessing pellets.... Over the years I've tried, wood, phonebooks, paraffin wax (all too hard), water, plumbers putty, playdoh, and ballistics gel (IMO all too soft and/or temperature sensitive), and I recently tried a bar of clear soap, which showed promise, so I ordered some melt-and-pour soap online, and after a few initial test shots, cast it into some bricks for pellet testing.... I cast the bricks in 8 x 8 square Pyrex dishes, about 1.5" thick, and using my Grouse gun, shot into the edge of the bricks.... This gun shoots at 20 FPE quite consistently over 16 shots, with lighter pellets achieving about 19 FPE and heavy ones about 21 FPE, which is typical for a PCP.... Here are the results, and some observations....
Here is a series of posts from a thread on another Forum where I tested a variety of pellets at several energy levels in melt-and-pour soap.... I am just copy-pasting the posts below.... The first set of tests are .22 cal at 20 FPE....
Every once in a while I try and find a new test medium for assessing pellets.... Over the years I've tried, wood, phonebooks, paraffin wax (all too hard), water, plumbers putty, playdoh, and ballistics gel (IMO all too soft and/or temperature sensitive), and I recently tried a bar of clear soap, which showed promise, so I ordered some melt-and-pour soap online, and after a few initial test shots, cast it into some bricks for pellet testing.... I cast the bricks in 8 x 8 square Pyrex dishes, about 1.5" thick, and using my Grouse gun, shot into the edge of the bricks.... This gun shoots at 20 FPE quite consistently over 16 shots, with lighter pellets achieving about 19 FPE and heavy ones about 21 FPE, which is typical for a PCP.... Here are the results, and some observations....
Top row right to left:
Gamo Match Wadcutter 13.7 gr.
Gamo Hunter Domed 15.1 gr.
Gamo Magnum Pointed 15.1 gr.
Gamo Roundball 15.1 gr.
Gamo Master Point 16.4 gr.
Gamo TS-22 Rounded Point 21.6 gr.
Hatsan Domed 14.3 gr.
Predator Big Boy Pointed 26.0 gr.
The wadcutter shortened and expanded slightly, and had the least penetration.... The roundball left a very narrow wound channel, as did the TS-22 which penetrated deeply....
Gamo Match Wadcutter 13.7 gr.
Gamo Hunter Domed 15.1 gr.
Gamo Magnum Pointed 15.1 gr.
Gamo Roundball 15.1 gr.
Gamo Master Point 16.4 gr.
Gamo TS-22 Rounded Point 21.6 gr.
Hatsan Domed 14.3 gr.
Predator Big Boy Pointed 26.0 gr.
The wadcutter shortened and expanded slightly, and had the least penetration.... The roundball left a very narrow wound channel, as did the TS-22 which penetrated deeply....
 |
| This image copyright R. Sterne, of the Crosman Airgun Forum. |
Bottom row, left to right:
RWS Hobby 11.9 gr. Wadcutter
RWS MeisterKugeln 14.0 gr. Wadcutter
RWS Super Hollow Point 14.3 gr.
RWS Super Dome 14.3 gr.
RWS Super Point 14.3 gr.
Crosman Wadcutter 14.3 gr.
Crosman Premier 14.3 gr.
Crosman Premier Hollow Point 14.3 gr.
The wadcutters, in particular the Hobby, showed some shortening and expansion, with a slightly wider initial wound channel.... The RWS Hollow Point stripped off the nose ring, leaving the aft part to penetrate, and left a larger wound channel where the nose stripped off just after entry.... The Crosman Premier Hollowpoint acted basically like it was a roundnose....
Want to read more? Click This Link:
READ THE FULL THREAD BY CLICKING HERE
No comments:
Post a Comment